Untitled-54
Untitled-9
9705

Introduction:
Solvent Based Temporary Protective

The tough General Chemical’s Peelable coating clear film is still the best method of preventing scratches and abrasions and strips cleanly away from the surface leaving no residue. It will also act as a masking against paint overspray.

Main Advantages

  • Results in a reduction of labor costs.
  • Once cured, it provides an extremely tough, uniform film.
  • Curing time can be cut considerably with the use of heat lamps (100°F), circulation of air and other factors.
  • Easily removed. Peels off in sheets which eliminates messy hand scrapping.
  • Safe, non-flammable.
  • Suitable for all substrates including polycarbonates, plastic and painted surfaces.

Drying Time:
It is critical that Our Peelable coating film is allowed to cure dry. Drying time will vary according to humidity, temperature and weather condition. The evaporation of water will be speeded by air movement and warmth supplied by natural and mechanical means.

Curing:
It is possible to get a 3 mil tack free dry coating film in less than one hour drying in air at ambient temperature. For maximum tensile strength , 12 hour drying time is better. Blowing air past the surface of the wet film, drying time can be shortened. Heated air up to temperature of 115f can also help in drying time. Mask cures upon water evaporation.

Dry time is dependent upon temperature, humidity, air movement and thickness of the coating. Curing may be accelerated by forced dry air up to 100 degrees Fahrenheit. Force dry coatings can cure in less than 10 minutes. Most coatings without assist will dry in a few hours. It is imperative that Liquid Mask be thoroughly cured and dry, before an attempt is made to peel the coating from the substrate. Cured coating is transparent throughout. Cured Mask is water resistant. Surfaces coated with Mask can be water mopped.

Application by roller might require a few coats. Thick coating peels in one large continuous sheet. Thin coatings will break in areas of coating weakness. Mask is water based for safe use and easy water clean up. Dry coatings are water resistant. When applying Mask use the same protection as used while applying paint.

Adhesion:
Our Peelable coatings is a temporary protective Peelable coating and adhesion is low.

Process:
Our Peelable coatings once completely dry are resistant to water and solvent and acts as a mask against sprayed emulsion paints, lacquers, oil or grease and water.

Removal:
The dry Our Peelable coatings strippable coating film can be easily removed either by hand stripping or other means. Our Peelable coatings are thermoplastic. Do not try to remove in freezing conditions. Our Peelable coatings becomes brittle in freezing condition.

Clean Up:
Our Peelable coating is a water-based product and you can clean spray equipment and brushes with water. Do this immediately before peelalbe coating starts to dry.

Paint Spray Booth Peelable Coatings

Developed for application to walls and floors of paint spray booths and surrounding area. The peelable masking film protects the walls and floors of the spray booth area from paint overspray and yet maintains its integrity by not allowing solvent penetration. It can be quickly peeled from any surface, even when heavily laden with overspray.

General Chemical’s water based & solvent based fast drying Peelable / Paint spray booth strippable coatings are temporary protective strippable coatings for Spray booths, Paint Booths, industrial floors & various surfaces such as paint booths spray booths, glass, decal, storage parts wood and others to protect it temporarily during industrial process or in material handling.

For More Information View: Paint Booths

Preservation & Storage System

Our Peelable coatings are used for long term preservation for the external storage of vehicles and equipment saving the use of internal storage space and also when they are loaded on deck, protected from the corrosive elements during the long sea voyage .

Similar applications apply to any components that may be exposed to the elements for long periods of time that would be affected by U.V. degradation, acid rain or corrosion. The General Chemical Preservation System Peelable maskants are non toxic, non flammable and the water borne skin tight film will not damage plastic or painted surfaces.

For More Information View: Paintshield 5720

Coverage

One liter will cover approximately 4 square meters at a dry film thickness of 100 microns. You can also use following chart to calculate in mil thickness and gallon coverage.

Approximate Square Feet Coverage Per Gallon of General Chemical’s Peelable coatings:

General Chemical has a complete line of Peelable Masks to meet your challenging requirement. If we do not have something to meet your specific requirement, than we will develop it by working with you to meet that need for strippable coating.

  • Stripcoat 4710

    Stripcoat 4710 is a solvent based temporary protective peelable strippable black coating.  Stripcoat 4710 offers excellent hiding properties to protect from light sources for optical mirrors, silicon wafers, glass, photo masks, platter, optical media, and leaves no oil residue.

    buy-now-blue

    View Product
  • Stripcoat 2100

    ADDITIONAL $26 UPS HAZ-MAT FEE

    Stripcoat 2100 is a solvent based water resistant thing strippable clear coating.

    buy-now-blue

    View Product
  • Plate Off Mask 4210

    ,

    Plate Off  Mask 4210 is a BLUE solvent based MASKANT Polymeric Vinyl Peelable Coatings provide protection in two ways; by forming tough, flexible films with extremely low , they stop substrate corrosion caused by electrolytic action or the presence of water-borne oxygen. In addition, the usually thick film provides physical protection against surface damage, abrasion or move and have proven that they provide a high degree of protection against acid and alkali attack

    buy-now-blue

    View Product
  • Liquid Mask 4560

    ,

    Liquid Mask 4560 is our Highest viscosity clear solvent based strippable coating engineered for high film deposit

    Liquid Mask 4560 has excellent water and acid resistance to 200F.

    buy-now-blue

    View Product
  • Blue Plate Off Mask 4300

    ,

    Our Highest viscosity Blue Solvent Based strippable coating engineered for high film deposit; excellent water and acid resistant to 200F .  Price can be reduced for larger quantity, please contact us for more information.

    buy-now-blue

    View Product